HY-SW2051-TH / How to Setup Hybrone Smart Temperature & Humidity Sensor ?

About the Smart Temperature & Humidity Sensor

HY-SW2051-TH

STEP 1

Hybrone Account

First of all, you must have a Hybrone Cloud account to deploy and manage the Hybrone Temperature & Humidity Sensor.

You can complete the device setup process by logging into your Hybrone account with the Hybrone Mobile application. In your account, select the location where you want to add the device and then click the add new devicebutton. The add new device wizard will be launched.

Communication Definitions and Considerations
An active internet connection is required to track the device and receive notifications. Device setup is done with the Hybrone mobile application.The instructions on the application show the necessary procedures.
Before starting the setup, router settings may need to be adjusted. The device supports 2.4 GHz Wi-Fi frequency band. The router Wi-Fi frequency must be set to 2.4 GHz band. Also make a note of the Wi-Fi name and password. The device sends health information to the Hybrone server every 8 hours in the absence of any alarm. If 3 consecutive times no health information is received, the device is considered offline.

STEP 2

Adding a Device to Hybrone

In Hybrone Mobile application, the wizard for adding a new device is started and the instructions on the screen are followed respectively. Here, device type "IoT Sensor" and device brand "Hybrone" should be selected. In the next steps, your device will be found automatically and the wizard will continue and the device addition process will be completed.

If your device cannot be added automatically, you can try the manual addition method.

 By opening the manual addition screen, you must first enter the Wi-Fi information you want to connect the device to the internet and then set the connection mode on the device.

Activating the Device

Once your device has been successfully added, the new device addition wizard will direct you to the device subscription package selection screen. On this screen, select the appropriate subscription package, continue the steps in the wizard and complete the process of activating your device in your Hybrone account.

Utilization

To open the battery compartment back cover slide and remove the insulation sheet.

When the batteries of the device run out, please select Alkaline batteries instead of Carbon-Zinc batteries.

a. Connect your smartphone to a 2.4GHz Wi-Fi network connect.

b. Enter your Wi-Fi password correctly.

c. Your phone must support Android 5.0+ or iOS 13.0+  support.

d. Limit the number of devices connected to the Wi-Fi router in the event that it arrives, the unused  try to disable the devices  or try again with another Wi-Fi router.

d) If the number of devices connected to the Wi-Fi router reaches the limit, try disabling unused devices or try again with another Wi-Fi router.

Installation

The area where you want to mount the sensor use a clean, dry wipe to clean the sensor.

To place the sensor where you want it remove the adhesive tape, for fixing strong for about 10 seconds press firmly.

(Adhesive tape is for single use only).

ATTENTION
Please use alkaline batteries and avoid power consumption. network immediately after installing the batteries to avoid configure the connection. Please remove heat sources keep away. Suitable for indoor use only

Functions

1. Configure High Accuracy Measurement approximately 30 minutes after completion, temperature and humidity value is the current ambient value will start to display with high accuracy.

Please keep the device away from any heat source keep it away.

2. Changing the Temperature Unit Change the temperature unit switch between Celsius and Fahrenheit to briefly press the reset button in the setting Press.

3. Historical temperature and humidity within your package you can access the data.

4. Temperature and humidity outside the ranges you set you can receive notifications from the app when it comes out.

5. When the battery power is low, the device will send a notification through the application.

FREQUENTLY ASKED QUESTIONS

1. When does the temperature and humidity value calibrate? 

Approximately 30 minutes after the configuration is completed, the temperature and humidity value will start to display the current environmental values.

2. When is the temperature and humidity displayed in the application not updated?

a) When the difference between the ambient temperature and the temperature in the application is < ± 0.5°C.

b) When the difference between the ambient humidity and the humidity in the application is < ± 5%.

3. When are the temperature and humidity on the screen synchronized with the data in the application?

a) After the network configuration is completed.

b) When the device's temperature and humidity are reported to Hybrone Cloud.

c) When there is a change of ≥ 0.5°C in ambient temperature or ≥ 5% in ambient humidity, and 2 minutes after power is supplied to the device, the temperature and humidity will be instantly reported to Hybrone.

d) When a change of < 0.5°C in ambient temperature or < 5% in humidity is detected, the temperature and humidity will be reported to Hybrone Cloud 1 hour later.